 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| AC-DC 150-300 Watts SML Series * * * * * * * Small Size - 4" x 6" Footprint Single Outputs 12-54 VDC High Power Density 150 W Convection-cooled 300 W Fan-cooled Temperature-controlled Fan PFD & Fan Fail Signals xppower.com Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor Earth Leakage Current Input Protection * * * * * * * 90-132 / 180-264 VAC autoranging 47-63 Hz 6.30/3.15 A at 115/230 VAC 70 A max at 230 VAC, cold start Complies with EN61000-3-2 Class A 3.5 mA max at 230 VAC Internal 6.3 A / 250 VAC fuse General Efficiency Isolation * 75% minimum, 230 VAC 100% load * 3000 VAC Input to Output 1500 VAC Input to Ground 250 VDC Output to Ground * 30 kHz typical * Up to 6.25 W/In3 * Open collector signal is LOW when DC is OK * Green LED to indicate power on * 100 kHrs per MIL-HDBK-217F at +30 C Switching Frequency Power Density PFD Signals MTBF Output Output Voltage Output Voltage Trim Minimum Load Initial Set Accuracy Start Up Delay Start Up Rise Time Hold Up Time Total Regulation Over/Undershoot Transient Response Ripple & Noise Overvoltage Protection Overtemperature Protection Overload Protection Fan Output Aux Output * * * * * * * * * * * * * * * * See tables 5% See tables 1% 1 s max 20 ms min at 120 VAC 20 ms min at 120 VAC & 80% load 1% 5% max at turn on/off 5% max. deviation, recovery to within 1% in 500 s for a 50% load change 1% pk-pk, 20 MHz BW, see note 1 <130% Vnom, recycle input to reset Unit shuts down with auto recovery, measured internally 110-140%, trip & restart (Hiccup mode) with auto recovery 12 VDC at 500 mA, temperature-controlled (available on 150 W model only) 12 VDC at 500 mA (12.0-14.5 VDC) Environmental Operating Temperature * -20 C to +70 C, derate from +50 C at 2.5%/C Cooling * 150 W convection-cooled, 300 W with internal fan Operating Humidity * 5-90% RH, non-condensing Storage Temperature * -20 C to +85 C Operating Altitude * 3000 m Vibration * 5-50 Hz, 7.35 ms2 on X,Y & Z axis EMC & Safety Emissions Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Safety Approvals * EN55022, level B conducted FCC Part 15 Subject J Class B * EN61000-3-3 amendments 1 & 2 * EN61000-4-2, level 2 Contact, Level 3 * EN61000-4-3, level 3 V/m Perf Criteria A * EN61000-4-4, level 2 Perf Criteria A * EN61000-4-5, level 3 Perf Criteria A * EN61000-4-6, level 3 V Perf Criteria A * EN60950-1, UL60950-1, CSA22.2 No 60950-1 AC-DC Models and Ratings Output Power Output Voltage 12.0 V 13.5 V 15.0 V 18.0 V 24.0 V 27.0 V 30.0 V 36.0 V 48.0 V 54.0 V 12.0 V 13.5 V 15.0 V 18.0 V 24.0 V 27.0 V 30.0 V 36.0 V 48.0 V 54.0 V Output Current Min 1.25 A 1.11 A 1.00 A 0.85 A 0.63 A 0.55 A 0.50 A 0.42 A 0.32 A 0.28 A 1.25 A 1.11 A 1.00 A 0.85 A 0.63 A 0.55 A 0.50 A 0.42 A 0.32 A 0.28 A Max(2) 12.50 A 11.10 A 10.00 A 8.33 A 6.70 A 5.55 A 5.00 A 4.17 A 3.13 A 2.78 A 25.00 A 22.20 A 22.00 A 16.66 A 12.55 A 11.00 A 10.00 A 8.33 A 6.25 A 5.55 A Ripple & Noise(1) 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% SML Model Number SML150PS12 SML150PS13 SML150PS15 SML150PS18 SML150PS24 SML150PS27 SML150PS30 SML150PS36 SML150PS48 SML150PS54 SML300PS12 SML300PS13 SML300PS15 SML300PS18 SML300PS24 SML300PS27 SML300PS30 SML300PS36 SML300PS48 SML300PS54 150 W ) 300 W 2.00 (50.8) Notes 1. Measured at 20 MHz bandwidth with 0.1 F ceramic capacitor in parallel with 22 F electrolytic capacitor. 2. Peak power of 600 W can be taken for 500 s. Mechanical Details 4.00 (101.6) 2.00 (50.8) 1.00 (25.4) Pin 1 2 3 4 5 6 CN1 Fan Return +12 V CN2 Signals +12 V, 0.5 Auxiliary Return PFD LED Drive+ Fan LED Drive + PFD Fan Fail A A 1.00 (25.4) 4.00 (101.6) 1.00 (25.4) 0.08 (2.0) A 4.00 (101.6) 3.00 (76.2) 2.00 (50.8) L All dimensions are in inches (mm). Weight approx 1.75 lb (800 g). 4.00 (101.6) A N G VVV+ V+ 1 A (8 places) CN2 A A CN1 6 1 2 0.08 (2.0) 0.50 (12.7) 1.00 (25.4) 4.00 (101.6) 0.24 (6.3) 6.00 (152.4) ) 0.20 (5.2) 2.00 (50.8) A A M4 x 0.7 1.00 (25.4) 0.10 (2.7) 1.00 (25.4) 0.24 (6.3) 0.20 (5.2) 1.00 (25.4) 4.00 (101.6) 1.00 (25.4) M4 Notes 1. Fan drive connector CN1 mates with Molex 22-01-1022 or equivalent with Series 2759 or 5159 crimps. 2. Signal connector CN2 mates with JST XHP-6 or equivalent with JST SXH-002T-P0.6 crimps. 3. Auxiliary 12 V 500 mA supply is regulated between 12 V to 14.5 V. 4. External LED can be connected between `PFD LED Drive +' and `PFD', max current is 5 mA. 5. External LED can be connected between `Fan LED Drive +' and `Fan Fail', max current is 5 mA. 6. Input/Output connector is Howder, part H3-95-7P. 7. Optional cable harness available. Order part number SML LOOM KIT. 8. Maximum mounting screw penetration 0.15 (4.00) from case outer surfaces. 17-Apr-07 |
Price & Availability of SML300PS12
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |